使用保養.維護

　　在更換蝸輪箱潤滑油和右機腿蝸輪箱液壓油時,注意里邊的熱油溢出小心灼傷.

　　1.蝸輪箱的潤滑.

　　本機采用油浸式潤滑,采用N320渦輪潤滑油潤滑.加油容量3.5升,浸油深度為減速器箱體油標塞注滿為準.在第一次使用時,機器運轉10天左右應更換新油,以后如長時間連續工作.每6個月更換一次,如每天工作8小時10個月更換一次,減速器軸承處油脂潤滑點,每運轉20天補充一次.當工作環境超過45度時,應考慮冷卻或降低減速器的負荷.

　　2.液壓油

　　機器工作溫度適宜5-35度.使用油溫10-65度.液壓油要定期更換,初次使用在200小時后應更換液壓油.以后每半年換一次(因為季節不同).液壓箱里的液壓油應隨周圍環境溫度的變化而選擇不同的粘度的液壓油.加換油時必須用200目銅絲布過濾.注意必須使用抗磨液壓油.

　　技術安全及注意事項

　　程控.數顯切紙機操作工必須上崗培訓,嚴格按照說明書操作設備.開機后,如發現意外情況和不正常的響聲和卡滯現象,必須立即停車檢查.切紙機在調試,換刀時必須停止主電機.換刀結束后手柄使刀床往復運轉一周,以免造成人身和設備損壞.工作時工作臺上面不允許放置油壺及各類工具等.與裁切工作不相關物品.機器運轉中嚴禁把手伸進裁切刀下部,即使在停車狀況下,也嚴禁把手伸入切刀下換刀,調整等工作.勿將手臂等伸過刀口線推,取裁切物,如不行需將手臂伸過刀口線工作.必須放置自備保險墊加以保護.以免發生意外造成人身傷害.

　　如違反上述規定而造成的意外和人身傷害,生產廠家概不承擔任何責任..